- Pl2303 Mac Os X Driver Download
- Pl2303 Os X Drivers Update
- Pl2303 Os X Drivers Downloads
- Pl2303 Os X Drivers Windows 10
Programator PIC K150 nie działa
Uruchomiłem na win 8,1. Poczytac pdf -jaki system co i jak -sa takze stery Ps.Jest tez funkcja przywróc wczesniejszy sterownik-mi pomogła-jak na urzadzeniu jest żółta strzałka... stery i program microbrn
- PL2303_DriverInstaller_1181_20170504.zip
- PL2303 Windows Driver User Manual v1.18.0.pdf
- PL2303_DriverInstallerv1.18.1_ReleaseNote.txt
- Hardware Certification Report - 1152921504626450757.pdf
- PL2303_CheckChipVersion_v1006.exe
- PL2303CheckChipVersion_ReadMe.txt
- PL2303_DriverInstaller_1181_20170504.exe
OS X: As the command line, run: sudo screen /dev/cu.PL2303-000012FD 115200. The USB to Serial device will likely be detected at a different address, so try using tab completion (hit the key) after entering /dev/cu.PL2303; Windows: First, determine the COM Port number. This may be displayed as a system notification when you connect the USB device.
Version 1.5.1 is available for Mac OS X on 64 bit, 32 bit and PPC machines. Prolific PL-2303 cables - official drivers for the genuine Prolific cables. Windows: PL2303 Windows Driver Download; Mac OS: PL2303 Mac OS X Driver Download; Android: PL2303 Android Driver SDK Solution; M-215+ is a dual-system(GPS + GLONASS) GNSS. If you ask me to recommended a replacement product, I will say GNSS200L Tri-system(GPS+GLONASS+GALILEO) GNSS.
Download file - link to post
PL2303_DriverInstaller_1181_20170504.zip > PL2303CheckChipVersion_ReadMe.txt
PL-2303 CheckChipVersion Tool Program v1.0.0.6
For Windows OS Only
System Requirement:
. USB 1.1/2.0/3.0 Host Controller
. Device using PL2303HX/X/EA/RA/SA/TA/TB version chips
. PL-2303 Windows Driver Installer v1.8.0 or above
. Supports the following Windows OS Family:
- Windows XP SP2 and above (32 & 64 bit)
- Windows Vista (32 & 64 bit)
- Windows 7 (32 & 64 bit)
- Windows 8/8.1/10 (32 & 64 bit)
NOTE:
- Windows 8 is NOT supported in HXA/XA chip versions (will show yellow mark Error Code 10).
- Windows 8 is supported only in following chip versions:
- PL2303HXD (HX Rev D)
- PL2303EA (ESD protection)
- PL2303RA (Built-in transceiver)
- PL2303SA (SOP8 package)
- PL2303TA (PL2303HXA/XA replacement)
- PL2303TB (12 GPIO)
Supported device ID and product strings:
. VID_067B & PID_2303 for " Prolific USB-to-Serial Comm Port "
. VID_067B & PID_2304 for " Prolific USB-to-Serial Comm Port " (PL2303TB chip)
. Other VID/PID based on PL2303 chip.
How to Run Tool Program
1. Install PL-2303 Windows Driver Installer v1.8.0 or above.
2. Plug PL2303 USB Device and go to Device Manager to check COM Port number.
3. Run PL2303CheckChipVersion tool and set COM Port number.
4. Click Check button to show PL-2303 chip version.
NOTE: This program cannot detect HXA/XA chip in Windows 8 and above.
Download Latest Driver here:
http://www.prolific.com.tw/US/ShowProduct.aspx?p_id=225 & pcid=41
Prolific Technology Inc.
http://www.prolific.com.tw
PL2303_DriverInstaller_1181_20170504.zip > PL2303_DriverInstallerv1.18.1_ReleaseNote.txt
PL2303 Driver Setup Installer, Prolific Edition v1.18.1
Setup Installer Revision Note History
System Requirement:
. USB 1.1/2.0/3.0/3.1 Host Controller
. Device using PL2303HXA/XA/HXD/EA/RA/SA/TA/TB version chips
. Supports the following Windows OS Family (32 and 64 bit):
- Windows XP SP3
- Windows Server 2003
- Windows Vista
- Windows Server 2008
- Windows 7
- Windows Server 2008R2
- Windows 8
- Windows Server 2012
- Windows 8.1
- Windows Server 2012R2
- Windows 10 (TH1/TH2/RS1/RS2)
- Windows Server 2016
NOTE:
- PL2303HXA/XA EOL chip versions (discontinued) will NOT be supported in Windows 8/8.1/Server2012/Server2012R2 and Windows 10 onwards.
- Download latest PL2303 CheckChipVersion tool program to check chip version in Windows 7. (Or contact your cable vendor)
- Prolific recommends cables with PL2303HXD or PL2303TA chip.
- Windows 98/ME/2000/XP driver technical support are discontinued.
Supported device ID and product strings:
. VID_067B & PID_2303 for " Prolific USB-to-Serial Comm Port " (PL2303 series)
. VID_067B & PID_2304 for " Prolific USB-to-GPIO/PWM Port " (PL2303TB chip)
Driver Versions:
-------------------
- WDF WHQL Driver: v3.8.12.0 (03/03/2017) - for Windows 7/8/8.1/10; Server2008/2008R2/2012/2012R2/2016
- WDM WHQL Driver: v2.1.51.238 (10/22/2013) - for Windows 2000/XP/Server2003
Release Notes:
---------------
PL2303 Driver Installer v1.18.1
Installer & Build date: 1.18.1 (2017-05-04)
GUID:ECC3713C-08A4-40E3-95F1-7D0704F1CE5E
Installer Driver v1.18.1 (05/04/2017):
Revision Change:
--------------------------------
. Fixed silent installation function (/s syntax)
Windows WDF WHQL Driver v3.8.12.0 (03/03/2017):
Driver Revision Change:
--------------------------------
. Added WDF co-installer WdfCoInstaller01009.DLL and SER2PL.DLL:
- Fixed Windows Vista driver support installation issue.
- Modify/Added several baud-rate support display in Driver Properties
NOTE: Actual baud-rate setting is still dependent on the serial port software settings.
Previous History:
Driver v3.8.10.0 (Driver Installer v1.17.0):
--------------------------------------------------------
. Fixed 1200bps baud rate data error customer issue.
. Fixed docking system sometimes cannot detect device during suspend-resume burnin test.
Driver v3.8.30 (Driver Installer v1.16.0):
-----------------------------------------------------------
. Fixed COM port no response (freeze) when doing continuous quick USB hotplug with serial mouse attached.
Driver v3.8.2.0 (Driver Installer v1.15.0): {unreleased}
------------------------------------------------------------
. Fixed RS485 compatibility (using RTS pin control) in PL2303HXD OTPROM Writer setting.
- For RS485 cable based on Prolific reference schematic, need to use latest EEWriter v2.2.0.0 or above.
Driver v3.8.1.3 (Driver Installer v1.14.0):
------------------------------------------------------------
. Formal submit driver for Windows 10 Redstone version 1607 Build 14393 (Anniversary Update) and Server 2016 HLK certification.
. Fixed customer issue for 19200bps baudrate timing (PL2303TA chip) on BGM device.
Driver v3.8.0.0 (Driver Installer v1.13.0): {unreleased}
------------------------------------------------------------
. Add Windows 10 Device Guard compatibility (Hypervisor Code Integrity Readiness HLK Test).
. Fixed Notebook PC USB Docking hotplug issue in Windows 7 and Intel USB 3.0 host (cannot release COM port).
Driver v3.6.81.357 (Driver Installer v1.12.0):
-----------------------------------------------------------
. Fixed timing delay issue.
Driver v3.6.78.350 (Driver Installer v1.11.0):
-----------------------------------------------------------
. Fixed customer BSOD issue when plug in USB 3.0 host controller under Windows 8.1.
. Supports GPIO default value configuration in external EEPROM or OTPROM using EEWriter v2.1.0.0.
. Passed Windows 10 logo certification (HLK).
Driver v3.4.67.325 (Driver Installer v1.10.0):
----------------------------------------------------------
. Fixed Win7/8 to WinXP data transfer customer issue (38400bps). Adjust timeout constant.
. Fixed problem with SecureCRT program when setting DTR/DSR flow control.
. Fixed ClearCommError issue.
. Added 5787 and 300kbps baudrate support.
. Supports " IRP_MJ_CLEANUP " . Fixed customer application cannot re-open COM port after closing port.
. Improve device enumeration when PC reboots and device is plugged in.
Driver v3.4.62.293 (Driver Installer v1.9.0):
---------------------------------------------------------
. Driver will delay 1.5ms when AP execute GET_MODEMSTATUS.
. Fixed teraterm timeout/slow response issue.
. Fixed GPIO 2 & 3 function for HXD chip.
. Add 3250000bps baud support.
. GPIO 2,3 set as default input pin.
. Add auxiliary GPIO 4~7 driver support for HXD chip.
. Fixed modem issue (Disable SerialWdmFileRead).
. Add 256000 bps baud support for PL2303TA/TB.
. Fixed customer VB AP issue.
. Improve Serial Mouse enumeration.
Driver v3.4.48.272 (Driver Installer v1.8.0 & 1.8.19):
-------------------------------------------------------------------
. Fixed 110 bps on PL2303RA/SA/EA/TA/TB.
. Modify CheckChipVersion API (do not lock VID/PID).
. Fixed HXD chip is detected as HXC chip when BCD is written as 0300 instead of 0400.
. Added 80bps baud support.
. Fixed GPS device will be detected as MS Serial Ballpoint device.
. Fixed driver conflict with different VID/PID device. (STATUS_OBJECT_NAME_COLLISION)
. Fixed Teraterm loopback timeout issue.
Driver v3.4.36.247 (Driver Installer v1.7.0):
--------------------------------------------------------
. Fixed Putty/HTerm BSOD issue in Win7 64-bit. (for HXD chip only)
. Fixed HyperTerminal timeout issue when transferring large file. (for HXD chip only)
. Fixed Windows HCK logo test for Windows 8, 7, Vista WHQL driver.
Driver v3.4.31.231:
------------------------------
. Added driver support for new chip versions (PL2303EA, RA, SA).
. Supports new CheckChipVersion v1.0.0.2 and above program for checking all Prolific chip version.
. Fixed COM Port won't disappear when unplug PL2303 during data transfer (Write Timeout issue).
. Fixed Putty program BSOD issue on continuous transfer at 115200bps.
. Fixed 12Mbps baudrate support for PL2303TB chip version.
. Does NOT support Windows 8 for EOL chip versions (PL2303H, PL2303HXA, PL2303XA).
. For Windows 8: use PL2303HXD, PL2303TA, PL2303EA, PL2303SA, PL2303RA, PL2303TB.
Driver v3.4.25.218:
------------------------------
. Added driver support for Prolific next-gen USB-to-Serial chips (Codename TA/TB).
- old driver will not work on baudrates higher than 115200bps.
. No driver functional difference for current H/HX/X chip versions.
Driver v3.3.17.203:
------------------------------
. Use different service name in INF file to avoid driver conflict with XP INF driver.
- change line in INF file to {Serial.SVCDESC = " Prolific Serial port WDFdriver " }
. Added USB Selective Suspend power saving feature requested by Notebook PC vendors.
- Chip will go to sleep mode when idle for 10 seconds and COM port not open.
- Chip will NOT go to sleep mode when COM port is OPEN.
- requires to write Remote Wakeup in external EEPROM.
. Modify " SerialUndoExternalNaming " routine.
- Fix COM port is not removed in registry when device is unplug and program still open.
- update registry HKEY_LOCAL_MACHINEHARDWAREDEVICEMAPSERIAL COMM when unplug and replug.
. Added support for TransmitCommChar() function.
. Added SpinLock function to fix customer GPS application.
Windows WDM 2000/XP/Server2003 Driver v2.1.51.238 (10/22/2013)
Beginning September 2014, Windows XP driver will not be updated anymore.
Driver Change from v2.1.44.226 (Driver Installer v1.8.0 & 1.8.19):
------------------------------------------------------------------
. Driver will delay 1.5ms when AP execute GET_MODEMSTATUS.
. Fixed GPIO 2 & 3 function for HXD chip.
. Add 3250000bps baud support.
. GPIO 2,3 set as default input pin.
. Add auxiliary GPIO 4~7 driver support for HXD chip.
. Add 256000 bps baud support for PL2303TA/TB.
. Improve Serial Mouse enumeration.
. Fixed WHQL test using HCK 2.0.
Driver Change from v2.1.35.211 (Driver Installer v1.7.0):
---------------------------------------------------------
. Fixed 110 bps on PL2303RA/SA/EA/TA/TB.
. Modify CheckChipVersion API (do not lock VID/PID).
. Fixed HXD chip is detected as HXC chip when BCD is written as 0300 instead of 0400.
. Added 80bps baud support.
. Fixed GPS device will be detected as MS Serial Ballpoint device.
. Fixed Disable-Enable device issue in Windows 2000 Device Manager.
Driver Change from v2.1.30.193:
------------------------------
. Fixed write timeout intermittent issue (COM port won't disappear) during USB surprise removal.
. Fixed new Windows HCK logo test for XP WHQL driver.
Driver Change from v2.1.27.185:
------------------------------
. Added driver support for new chip versions (PL2303EA, RA, SA).
. Supports new CheckChipVersion v1.0.0.2 and above program for checking all Prolific chip version.
. Fixed COM Port won't disappear when unplug PL2303 during data transfer (Write Timeout issue).
. Fixed 12Mbps baudrate support for PL2303TB chip version.
Driver Change from v2.0.16.166:
------------------------------
. Added driver support for Prolific next-gen USB-to-Serial chips (Codename TA/TB).
- old driver will not work on baudrates higher than 115200bps.
. No driver functional difference for current H/HX/X chip versions.
Driver Change from v2.0.13.130:
------------------------------
. Use different service name in INF file to avoid driver conflict with Vista/7 INF driver.
- change line in INF file to {Serial.SVCDESC = " Prolific Serial port WDMdriver " }
. Added 10ms delay (downstream buffer) on close COM port to fix customer MCU application.
Language Support:
- English (default)
- Chinese (Traditional)
- Chinese (Simplified)
- Japanese
Download Latest Driver here:
http://www.prolific.com.tw/US/ShowProduct.aspx?p_id=225 & pcid=41
Counterfeit Warning!!!
Please be warned that counterfeit/fake PL-2303HX Chip Rev A (or PL-2303HXA) USB to Serial Controller ICs using Prolific's trademark logo, brandname, and device drivers, are being sold in the China market. Counterfeit IC products show exactly the same outside chip markings but generally are of poor quality and causes Windows driver compatibility issues (Yellow Mark Error Code 10 in Windows 7 Device Manager). We issue this warning to all our customers and consumers to avoid confusion and false purchase. Only purchase branded cables that provide technical support and warranty service. Prolific does not manufacture nor sell end-product cables.
How to Install Driver
1. Unplug any PL2303 USB Device first.
2. Run Driver Installer EXE program to install. Wait to finish.
3. Plug PL2303 USB Device and go to Device Manager to check COM Port number.
4. If PL2303 is embedded, you might need to restart Windows or rescan hardware in Device Manager.
5. Refer to PL2303 Windows Driver User's Manual.
NOTE: For silent install, include the syntax " /s " at the end of the EXE installer program.
For example: " PL2303_Prolific_DriverInstaller_v1.10.0.exe /s "
Prolific Technology Inc.
http://www.prolific.com.tw
PL2303_DriverInstaller_1181_20170504.zip > PL2303 Windows Driver User Manual v1.18.0.pdf
PL2303 Windows Driver User's Manual
For Driver Installer v1.18.0 Release
For Microsoft Windows Operating Systems
PL2303 USB-to-Serial Bridge Chip Family
Windows Driver Installer User Manual
WHQL Driver Version Information
? Driver Installer & Build date: 1.18.0 (2017-03-23)
?
?
GUID: ECC3713C-08A4-40E3-95F1-7D0704F1CE5E
WHQL WDM Driver: v2.1.51.238 (10/22/2013)
?
?
?
Windows 2000, XP, Server 2003 (32 & 64-bit)
https://sysdev.microsoft.com/en-US/Hardware/LogoVerificationReport.aspx?sid=1616428
WHQL WDF Driver: v3.8.12.0 (03/03/2017)
?
Windows 10 TH1/TH2/RS1/RS2 (32 & 64-bit)
?
Windows Vista, 7, 8, 8.1 (32 & 64-bit)
?
Compatible with Windows Server 2008/2008R2, Server 2012/2012R2, Server 2016 (64-bit)
?
Drivers automatically install via Windows Update (need Internet connection)
System Requirements
?
PC with USB 1.1/2.0/3.0/3.1 Host Controller (USB Port) and Windows OS.
?
USB Device with below PL-2303 chip versions and their supported OS Family:
Windows
Windows
Windows
Windows 10
2000 / XP
Vista / 7
8 / 8.1
TH1/TH2/RS1
Server 2003
Server2008/R2
Server2012/R2
Server 2016
(32 & 64 bit)
(32 & 64 bit)
(32 & 64 bit)
(32 & 64 bit)
PL-2303H
Yes
Yes
Not Supported*
Not Supported*
PL-2303HX (Rev A)
Yes
Yes
Not Supported*
Not Supported*
PL-2303X or XA
Yes
Yes
Not Supported*
Not Supported*
Yes
Yes
Yes
Yes
PL2303TA
Yes
Yes
Yes
Yes
PL2303TB
Yes
Yes
Yes
Yes
PL2303EA
Yes
Yes
Yes
Yes
PL2303RA
Yes
Yes
Yes
Yes
PL2303SA
Yes
Yes
Yes
Yes
Chip Version
PL-2303HX (Rev D) or
HXD
* - PL2303H, PL-2303HX (Rev A), and PL-2303X are EOL and discontinued chips and Prolific will not
provide Windows 8 (and above versions) driver support. New driver versions will show yellow mark (Error
Code 10) in Device Manager for these EOL chip versions under Windows 8 or above OS versions.
Prolific Technology Inc.
- 1 of 17 -
March 24, 2017
All information herein is subject to change without prior notice. Prolific Technology Inc. does not make any warranties regarding
the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial
damage, including but not limited to special, incidental, consequential, or other damages. No part of this document may be
reproduced or transmitted in any form by any means without the express written permission of the manufacturer.
PL2303 Windows Driver User's Manual
For Driver Installer v1.18.0 Release
For Microsoft Windows Operating Systems
Counterfeit Warning!!!
Please be warned that counterfeit/fake PL-2303HX Rev A (or PL-2303HXA) USB-to-Serial Controller
ICs using Prolific's trademark logo, product name, and drivers are being sold in the China market.
Counterfeit IC products show exactly the same outside chip markings but generally are of poor quality
and causes Windows driver compatibility issues (Yellow Mark Error Code 10 in Device Manager under
WinXP, Vista, and 7). This warning is issued to all customers and consumers to avoid confusion and
false purchase. Please purchase only from stores or vendors providing technical and RMA support.
Windows 7 Driver Installation
This section will guide you on how to install the PL-2303 Windows Driver. You can download the latest
Driver Installer program from Prolific Support website:
http://www.prolific.com.tw/US/ShowProduct.aspx?p_id=225 & pcid=41
Note: Please take notice of the installation order. First, run the Driver Installer Program before
plugging in the USB to Serial adapter. If you already plug the device during the driver installation, you
need to re-plug the device for Windows to enumerate the device and load the drivers installed. If your
device is embedded to the system, you might need to restart the system (or click rescan hardware
changes in Device Manager) to reload and install the driver.
The following steps will show how to install the device under Windows 7 (64-bit) OS as this is the most
inquired driver installation support received by Prolific. The procedures are the same and straightforward for all other supported Windows operating system versions.
Prolific Technology Inc.
- 2 of 17 -
March 24, 2017
All information herein is subject to change without prior notice. Prolific Technology Inc. does not make any warranties regarding
the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial
damage, including but not limited to special, incidental, consequential, or other damages. No part of this document may be
reproduced or transmitted in any form by any means without the express written permission of the manufacturer.
PL2303 Windows Driver User's Manual
For Driver Installer v1.18.0 Release
For Microsoft Windows Operating Systems
1.
Power on your computer and boot to Windows. Run or double-click the PL-2303 Windows Driver
Installer program.
2.
The InstallShield Wizard will be displayed to inform you that the PL-2303 USB-to-Serial driver
will be installed on your computer. Click Next to continue.
Prolific Technology Inc.
- 3 of 17 -
March 24, 2017
All information herein is subject to change without prior notice. Prolific Technology Inc. does not make any warranties regarding
the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial
damage, including but not limited to special, incidental, consequential, or other damages. No part of this document may be
reproduced or transmitted in any form by any means without the express written permission of the manufacturer.
PL2303 Windows Driver User's Manual
For Driver Installer v1.18.0 Release
For Microsoft Windows Operating Systems
3.
The PL-2303 Driver Installer program will then start to install the drivers needed.
4.
Click the Finish button to close the InstallShield program. If you have plugged the cable into the
PC while running the setup installation, please unplug and replug the cable for the system to
detect the device.
Prolific Technology Inc.
- 4 of 17 -
March 24, 2017
All information herein is subject to change without prior notice. Prolific Technology Inc. does not make any warranties regarding
the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial
damage, including but not limited to special, incidental, consequential, or other damages. No part of this document may be
reproduced or transmitted in any form by any means without the express written permission of the manufacturer.
PL2303 Windows Driver User's Manual
For Driver Installer v1.18.0 Release
For Microsoft Windows Operating Systems
5.
Plug in the USB to Serial adapter to the PC USB port. Windows should detect the driver as
Prolific USB-to-Serial Comm Port. Go to Device Manager and check for the 'Prolific
USB-to-Serial Comm Port' device and the COM port number assigned by Windows.
6.
You can also check the driver version by right-clicking on the 'Prolific USB-to-Serial Comm Port'
device and select Properties and Driver tab.
Prolific Technology Inc.
- 5 of 17 -
March 24, 2017
All information herein is subject to change without prior notice. Prolific Technology Inc. does not make any warranties regarding
the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial
damage, including but not limited to special, incidental, consequential, or other damages. No part of this document may be
reproduced or transmitted in any form by any means without the express written permission of the manufacturer.
PL2303 Windows Driver User's Manual
For Driver Installer v1.18.0 Release
For Microsoft Windows Operating Systems
Warning!!!
If you are encountering yellow mark (Error Code 10) for device in Device Manager under Windows XP,
Vista, or Windows 7, you need to contact the cable vendor or manufacturer for possible counterfeit
chip. Prolific does not manufacture or sell any end-user market products and will not provide or be
responsible for direct support to end-users.
Prolific Technology Inc.
- 6 of 17 -
March 24, 2017
All information herein is subject to change without prior notice. Prolific Technology Inc. does not make any warranties regarding
the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial
damage, including but not limited to special, incidental, consequential, or other damages. No part of this document may be
reproduced or transmitted in any form by any means without the express written permission of the manufacturer.
PL2303 Windows Driver User's Manual
For Driver Installer v1.18.0 Release
For Microsoft Windows Operating Systems
Windows Driver Installation (via Windows Update)
This section guides you on how to install the PL-2303 Windows Driver via Windows Update. You will
need an Internet connection to automatically download and install the drivers via Windows Update:
Operating Systems
Windows Update
Windows 7
Windows 8 / 8.1
(32 & 64 bit)
(32 & 64 bit)
?
?
Windows 10
Server 2016
(32 & 64 bit)
?
1.
Check if your Internet connection is OK. Plug in PL-2303 USB to Serial cable.
2.
Windows will automatically check Windows Update if driver is available and will download and
install the driver instantly.
Prolific Technology Inc.
- 7 of 17 -
March 24, 2017
All information herein is subject to change without prior notice. Prolific Technology Inc. does not make any warranties regarding
the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial
damage, including but not limited to special, incidental, consequential, or other damages. No part of this document may be
reproduced or transmitted in any form by any means without the express written permission of the manufacturer.
PL2303 Windows Driver User's Manual
For Driver Installer v1.18.0 Release
For Microsoft Windows Operating Systems
3.
Windows will then prompt you that Prolific USB-to-Serial Comm Port (COMx) is installed and
ready to use.
Prolific Technology Inc.
- 8 of 17 -
March 24, 2017
All information herein is subject to change without prior notice. Prolific Technology Inc. does not make any warranties regarding
the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial
damage, including but not limited to special, incidental, consequential, or other damages. No part of this document may be
reproduced or transmitted in any form by any means without the express written permission of the manufacturer.
PL2303 Windows Driver User's Manual
For Driver Installer v1.18.0 Release
For Microsoft Windows Operating Systems
4.
You can also right-click on the USB-Serial Controller device and click Update Driver.
Prolific Technology Inc.
- 9 of 17 -
March 24, 2017
All information herein is subject to change without prior notice. Prolific Technology Inc. does not make any warranties regarding
the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial
damage, including but not limited to special, incidental, consequential, or other damages. No part of this document may be
reproduced or transmitted in any form by any means without the express written permission of the manufacturer.
PL2303 Windows Driver User's Manual
For Driver Installer v1.18.0 Release
For Microsoft Windows Operating Systems
Prolific Technology Inc.
- 10 of 17 -
March 24, 2017
All information herein is subject to change without prior notice. Prolific Technology Inc. does not make any warranties regarding
the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial
damage, including but not limited to special, incidental, consequential, or other damages. No part of this document may be
reproduced or transmitted in any form by any means without the express written permission of the manufacturer.
PL2303 Windows Driver User's Manual
For Driver Installer v1.18.0 Release
For Microsoft Windows Operating Systems
Windows 8/8.1/10 Supported Chip Versions
This section will guide you on what PL-2303 chip versions are supported by Prolific in Windows 8:
Chip Version
Chip Availability
Windows 8/8.1/10 (32 & 64 bit)
PL-2303H
Discontinued (EOL)
No New Driver Support*
PL-2303HX (Rev A) or HXA
Discontinued (EOL)
No New Driver Support*
PL-2303X or XA
Discontinued (EOL)
No New Driver Support*
PL-2303HX (Rev D) or HXD
Available
Yes
PL2303TA
Available
Yes
PL2303TB
Available
Yes
PL2303EA
Available
Yes
PL2303RA
Available
Yes
PL2303SA
Available
Yes
* - New Driver does not support PL-2303H, PL2303HX (Rev A), and PL2303X in Windows 8/8.1/10. It will show a
yellow mark (Error Code 10) in Device Manager similar to what counterfeit chips would show.
Check Chip Version Tool
Prolific provides a tool program inside the driver package to check the chip version of your device:
http://www.prolific.com.tw/US/ShowProduct.aspx?p_id=225 & pcid=41
NOTE:
This tool will not work in Windows 8/8.1/10 if the PL-2303 device shows a yellow mark in Device
Manager. You need to use Windows 7 or XP to run the tool program for discontinued chip versions.
Prolific Technology Inc.
- 11 of 17 -
March 24, 2017
All information herein is subject to change without prior notice. Prolific Technology Inc. does not make any warranties regarding
the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial
damage, including but not limited to special, incidental, consequential, or other damages. No part of this document may be
reproduced or transmitted in any form by any means without the express written permission of the manufacturer.
PL2303 Windows Driver User's Manual
For Driver Installer v1.18.0 Release
For Microsoft Windows Operating Systems
Windows 8/8.1/10 Driver Installation
This section shows how to install the PL-2303 device in Windows 8 or 8.1 or 10 Operating System.
You can download the latest Driver Installer program from Prolific Support website:
http://www.prolific.com.tw/US/ShowProduct.aspx?p_id=225 & pcid=41
1.
Power on your computer and boot to Windows. Run or double-click the PL-2303 Windows Driver
Installer program. The InstallShield Wizard will be displayed to inform you that the PL-2303
USB-to-Serial driver will be installed on your computer. Click Next to continue.
Prolific Technology Inc.
- 12 of 17 -
March 24, 2017
All information herein is subject to change without prior notice. Prolific Technology Inc. does not make any warranties regarding
the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial
damage, including but not limited to special, incidental, consequential, or other damages. No part of this document may be
reproduced or transmitted in any form by any means without the express written permission of the manufacturer.
PL2303 Windows Driver User's Manual
For Driver Installer v1.18.0 Release
For Microsoft Windows Operating Systems
2.
The PL-2303 Driver Installer program will then start to install the drivers needed. Click the Finish
button to close the InstallShield program.
3.
Plug in the USB to Serial adapter to the PC USB port. Windows should detect the driver as
'Prolific USB-to-Serial Comm Port'. Go to Device Manager and check for the device and the
COM port number assigned by Windows. You can also check the driver version by right-clicking
on the 'Prolific USB-to-Serial Comm Port' device and select Properties and Driver tab.
Prolific Technology Inc.
- 13 of 17 -
March 24, 2017
All information herein is subject to change without prior notice. Prolific Technology Inc. does not make any warranties regarding
the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial
damage, including but not limited to special, incidental, consequential, or other damages. No part of this document may be
reproduced or transmitted in any form by any means without the express written permission of the manufacturer.
PL2303 Windows Driver User's Manual
For Driver Installer v1.18.0 Release
For Microsoft Windows Operating Systems
4.
The COM Port number for the PL-2303 is assigned by the Windows Operating System. If you
encounter a device that shows a yellow mark (Error Code 10), please check if the device is using
an old version Prolific chip (PL-2303HXA or PL-2303XA) or a counterfeit chip. As mentioned in
the previous sections, Prolific does not support old version chips in Windows 8 and above.
Prolific Technology Inc.
- 14 of 17 -
March 24, 2017
All information herein is subject to change without prior notice. Prolific Technology Inc. does not make any warranties regarding
the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial
damage, including but not limited to special, incidental, consequential, or other damages. No part of this document may be
reproduced or transmitted in any form by any means without the express written permission of the manufacturer.
PL2303 Windows Driver User's Manual
For Driver Installer v1.18.0 Release
For Microsoft Windows Operating Systems
Uninstalling the PL-2303 Driver
To uninstall the PL-2303 driver, follow the below steps:
1.
Click Start - Control Panel - Programs - Programs and Features - Uninstall a Program. Look for
the 'PL-2303 USB-to-Serial' program and click the Uninstall (Remove) button.
2.
InstallShield Wizard will then start the maintenance program and will prompt you to choose if you
want to modify, repair, or remove the driver. Click the Remove button and click Next to begin the
driver uninstall.
Prolific Technology Inc.
- 15 of 17 -
March 24, 2017
All information herein is subject to change without prior notice. Prolific Technology Inc. does not make any warranties regarding
the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial
damage, including but not limited to special, incidental, consequential, or other damages. No part of this document may be
reproduced or transmitted in any form by any means without the express written permission of the manufacturer.
PL2303 Windows Driver User's Manual
For Driver Installer v1.18.0 Release
For Microsoft Windows Operating Systems
3.
The InstallShield Wizard will prompt you to confirm to uninstall. Click Yes to continue.
4.
Wait for the InstallShield Wizard to complete the uninstall process. When complete, click Finish
to end the program. Wait for some few seconds until the 'PL-2303 USB-to-Serial' program is
removed from the Control Panel Uninstall (Add or Remove Programs) program list.
Prolific Technology Inc.
- 16 of 17 -
March 24, 2017
All information herein is subject to change without prior notice. Prolific Technology Inc. does not make any warranties regarding
the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial
damage, including but not limited to special, incidental, consequential, or other damages. No part of this document may be
reproduced or transmitted in any form by any means without the express written permission of the manufacturer.
PL2303 Windows Driver User's Manual
For Driver Installer v1.18.0 Release
For Microsoft Windows Operating Systems
5.
If you are using Windows Server versions or installed the driver thru Windows Update, you may
need to do this extra step if driver is not completely uninstalled. Plug back the PL2303 device to
the computer and go to Device Manager and right-click 'Prolific USB-to-Serial Comm Port'. Click
Uninstall and click enable the checkbox 'Delete the driver software for this device'. Click OK to
completely uninstall the driver.
Prolific Technology Inc.
- 17 of 17 -
March 24, 2017
All information herein is subject to change without prior notice. Prolific Technology Inc. does not make any warranties regarding
the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial
damage, including but not limited to special, incidental, consequential, or other damages. No part of this document may be
reproduced or transmitted in any form by any means without the express written permission of the manufacturer.
Pl2303 Mac Os X Driver Download
PL2303_DriverInstaller_1181_20170504.zip > Hardware Certification Report - 1152921504626450757.pdf
6/2/2017
Hardware Certification Report 1152921504626450757
Hardware certification report Approved
Private product ID:
13867838504789242
Shared product ID:
1152921504607169656
Submission ID:
1152921504626450757
Submission date:
4/5/2017
Completion date:
4/5/2017
Company:
Prolific Technology Inc.
Product name:
PL2303 USB to Serial Windows 7/8/10 Driver
Category:
Device
Product type:
Other Device
Qualification level:
1511, x64
1511, x86
Certified for Microsoft Windows 10 Client family version 1703, x64
Certified for Microsoft Windows 10 Client family version 1703, x86
Logo - Device - Compatible with Windows 7 x64
Logo - Device - Compatible with Windows 7
Certified for Microsoft Windows 8 Client family, x64
Certified for Microsoft Windows 8 Client family, x86
Certified for Microsoft Windows 10 Client family version 1607, x64
Certified for Microsoft Windows 10 Client family version 1607, x86
Certified for Microsoft Windows 10 Client family versions 1506 and
Marketing name:
PL2303 USB to Serial Bridge Controller IC
Certified for Microsoft Windows 10 Client family versions 1506 and
Certified for Microsoft Windows 8.1 Client family, x64
Certified for Microsoft Windows 8.1 Client family, x86
Signature Only - Microsoft Windows Vista family, x86
Signature Only - Microsoft Windows Vista family, x64
file:///C:/Users/mikechu/Downloads/HWCertReport_1152921504626450757.html
1/1
PL2303GC Data Sheet
File Name Release Date Version File Size
PL23XX_Prolific_DriverInstaller_v204.zip 2020/12/08 2.0.4 10782.28KB
Windows Driver Installer Setup Program
(For PL2303 HXD, SA, TA, TB, RA GC, GS, GT, GL, GE , GD, GR versions)
Installer version & Build date: 2.0.4 (2020-12-08)
- Windows 10 Certified WHQL Driver (TH1 1507, TH2 1511, RS1 1607, RS2 1703, RS3 1709, RS4 1803,RS5 1809,19H1 1903, 19H2 1909, 20H1 VB versions)
Windows Vista/7/8.1/10 (32 & 64-bit) WDF WHQL Driver: v3.8.31.0 (07/30/2019) / v5.0.15.0 (04/06/2020)
- - Windows 10 Certified WHQL Driver (TH1 1507, TH2 1511, RS1 1607, RS2 1703, RS3 1709, RS4 1803,RS5 1809,19H1 1903, 19H2 1909, 20H1 VB versions)
- Windows Vista, 7, 8.1 Certified WHQL Driver
- Compatible with Windows Server 2016, Server2008, 2008R2, 2012, 2012R2
- Auto-download driver via Windows Update (Windows 7, 8.1, 10)
Windows XP (32 & 64-bit) WDM WHQL Driver: v3.8.31.1 (07/30/2019) / v5.0.15.1 (04/06/2020)
- Windows XP Certified WHQL Driver
- Compatible with Windows 2000SP4 & Server2003
- Installer Language Support: English (default), Chinese (Traditional and Simplified), Japanese
- For Prolific USB VID_067B&PID_2303, PID_2304, PID_23A3, PID_23B3, PID_23C3,PID_23D3,PID_23E3,PID_23F3,PID_2323.
- Includes Certification Report, User Manual, Driver Release Notes, CheckChipVersion Tool
- Installer supports silent install (add '/s' parameter when running program)
File Name Release Date Version File Size
PL2303HXD_G_Driver_v2.0.0_20191204.zip 2019/12/04 v2.0.0 1296.49KB
Mac OS X Universal Binary Driver v2.0.0 (PKG file format)
For Mac OS Catalina (version 10.15) - see NOTE below.
For Mac OS Mojave (version 10.14)
For Mac OS High Sierra (version 10.13)
For Mac OS X Sierra (version 10.12)
For Mac OS X El Capitan (version 10.11)
For Mac OS X Yosemite (version 10.10)
For Mac OS X Mavericks (version 10.9)
For PL2303 H/HX/HXD/EA/RA/SA/TA/TB chip versions
For Prolific USB VID_067B&PID_2303 Only
For PL2303GC, GS, GT, GL, GE , GD chip versions
Includes Driver Installation Manual
NOTE: Mac OS High Sierra 10.13 introduces a new feature that requires user approval before loading new third-party kernel extensions. Go to System Preferences - Security & Privacy and click Allow.
Pl2303 Os X Drivers Update
File Name Release Date Version File Size
PL2303G_Linux_Driver_v1.0.4.zip 2020/06/05 v1.0.4 338.98KB
Linux Kernel 5.5 and above already includes built-in drivers for PL2303G Chip.
If you's Linux kernel is v2.6.15 ~v5.4, Please update the PL2303G Linux driver via PL2303G_Linux_Driver_v1.0.4.zip
Pl2303 Os X Drivers Downloads
File Name Release Date Version File Size
PL2303G_Android_v1000_20180827.zip 2019/03/18 v1.0.0.0 6602.81KB
PL2303G Android USB Host API SDK v1.0.0.0
Requirements:
- USB Device with PL2303GC, PL2303GS, PL2303GT, PL2303GL, PL2303GE controller chip
- Android-Powered Device (Tablet/Phones) with USB Host Mode Support
- Android 3.2 and above OS versions
SDK Package includes following:
1. PL2303 Sample Test Android App Software (supports Android 5.0)
- Single port (PL2303GSimpleTest.apk)
- Modem Status/Flow Control (PL2303G_ModemStatus.apk)
- GPIO Control (PL2303G_GPIO.apk)
- Multi-port (PL2303G_MultiSimpleTest.apk)
2. PL2303G Android Demo Apps User's Manual
3. PL2303G Android Sample App Source Code
4. PL2303G Android Java Driver Library (supports Android 5.0)
5. PL2303G Android App Development Reference Documents
Pl2303 Os X Drivers Windows 10
File Name Release Date Version File Size
PL2303G_Windows_GPIOTest_v1000.zip.zip 2020/05/04 v1.0.0.0 9384.32KB
PL2303G 16-GPIO LED Indicator Application Note
Includes GPIO Test Sample Program and Source Code